Results 1 – 10 of 10 Conceptos y protocolos de enrutamiento. Guía de estudio de CCNA exploration. (Cisco Networking Academy) by Graziani, Rick [Autor]; Díaz. Conceptos y protocolos de enrutamiento: guía de estudio de CCNA Exploration. by Rick Graziani; Allan Johnson. Print book. Spanish. Madrid: Pearson. CCNA Exploration Conceptos y protocolos de enrutamiento Introducción al from ITC TC at ITESM.
|Published (Last):||15 September 2012|
|PDF File Size:||10.64 Mb|
|ePub File Size:||18.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
You are commenting using your WordPress. You are commenting using your Twitter account. You are commenting using your Facebook account.
Esp CCNA2 4 0 Exploration Conceptos Y Protocolos De Enrutamiento
Notify me of new comments via email. Routing Protocols and Concepts Version 4. A static protocoloss that points to the next hop IP will have what administrative distance and ds in the routing table? What address can be used to summarize networks The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?
Refer to the exhibit.
It indicates that there are 8 hops between this router and the It represents the time, in milliseconds, it takes for a ping to reply when sent to the It indicates that there are 8 subnets in the destination network to which the router can forward packets. It indicates the number of consecutive bits, from the left, in the destination IP address of a packet that must match How will packets destined to the There is no matching interface associated with network A network administrator enters the following command into Router1: Router1 then receives a packet that is destined for After finding the recently configured static route in the routing table, what does Router1 do next to process the packet?
Given the output in the exhibit, how would a clock rate be determined for this link? The rate would be negotiated by both routers. The rate configured on the DTE determines the clock rate. The rate configured on the DCE determines the clock rate. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet?
Hosts on two separate subnets cannot communicate. The network administrator suspects dnrutamiento missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues?
A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the The engineer has been told to use only static routing for these company routers. Which set of conce;tos will establish connectivity between the two Ethernet networks? Which of the following are displayed by the Router show cdp neighbors command?
What two commands are required to provide connectivity between the A config ip route What two commands will change the next-hop address for the A config no network What happens to a static route entry in enrutamjento routing table conceeptos the outgoing interface is not available? The route is removed from the table. The router polls neighbors for a replacement route. The route remains in the table because it was defined as static.
The router redirects the static route to compensate for the loss of the next hop device.
A router has one static route to pprotocolos destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? The destination network no longer exists. The destination network is moved to a different interface on the same router.
Books by Rick Graziani (Author of Routing Protocols and Concepts, CCNA Exploration Companion Guide)
The path between the source and destination is upgraded with a higher bandwidth link. A topology change occurs where the existing next-hop address or exit interface is not accessible. The remote destination network interface has to be down for 15 minutes of maintenance. Why is it advisable to enter a next-hop IP address when creating a static route whose exit interface is an Ethernet network?
Adding the next-hop address eliminates the need for the router to do any lookups in the routing table before forwarding a packet. In a multi-access network, the router cannot determine the next-hop MAC address for the Ethernet frame without a next-hop address. Using a next-hop address in a static route provides a route with a lower metric.
In multi-access networks, using a next-hop address in a static route makes that route a candidate default route. What is the most likely cause for the line protocol being down? There is no cable connecting the routers. No clock rate has been set. Which static route should be configured on Router1 so that host A will be able to reach host B on the What two devices are responsible for converting the data from the WAN service provider into a form acceptable by the router?
Which of the following is true regarding CDP and the graphic shown? Which two statements describe functions or characteristics of CDP? It starts up automatically and allows the device to detect directly connected neighbor devices that use CDP.
It operates at the network layer and allows two systems to learn about each other. It creates a topology map of the entire network. It allows systems to learn about each other even if different network layer protocols are configured.
It forwards advertisements about routes for faster convergence. Which piece of information is available from examining the output of the command show ip interface brief? Which address can be used to summarize networks A router has one static route configured to each destination network.
Network Fundamentals Version 4. Leave a Reply Cancel reply Enter your comment here Fill in your details below or click an icon to log in: Email required Address never made public. Networking for Home and Small Businesses Version 4.