Changed layout of National Data Sheet to TI format. LevelC-UNLIM. to LMM. LMN. ACTIVE. PDIP. NFF. TBD. Call TI. Call TI. LMN Datasheet, LMN National Semiconductor Frequency to Voltage Converter Datasheet, buy LMN. LMN LM – Frequency to Voltage Converter, Package: Soic Narrow, Pin Nb= The LM Details, datasheet, quote on part number: LMN.
|Published (Last):||6 August 2009|
|PDF File Size:||20.52 Mb|
|ePub File Size:||3.63 Mb|
|Price:||Free* [*Free Regsitration Required]|
Klaus New Member Jul 3, The more versatile configurations provide differential ta- chometer input and uncommitted op amp inputs.
The two basic configurations offered include an 8-pin device. LM – 8 pin package As you show the 8 pin package circuit, I assume this is what you have – there is a 14 pin version as well. This version is well suited for single speed or frequency switching or fully buffered frequency to voltage conversion applications.
Stick with the LM I’m sure the LM is capable of doing what fatasheet want, it just needs some component changes to set the range. Welcome to our site! That range can give me a larger range to have a more accuracy signal to do speed control. Thank you a lot. Replacing a 4 pin leaded inductor with a 2 pin Started by gkmaia Yesterday at Also, I need to be very conservative wrt adding components. So, what can I do. The tachom- eter uses a charge pump technique and offers frequency doubling for low ripple, full input protection in two versions LM, LM and its output swings to ground for a zero frequency input.
Click here to register now. The input signal must therefore go positive AND negative for the circuit to work. Both of these configurations are available with an active.
Design Frequency to Voltage Circuit of LM2907N
Can any professional give me a design which datassheet achive a higher range of output, e. Thank you very much. Frequency to Voltage Converter. Sorry, can you give me any advice of which type can do such thing? This version is well suited for pm2907n. With this version the tachometer input may be floated and the op amp becomes suitable for active filter conditioning of the tachom- eter output.
Thank you for your reply. To participate you need to register. The more versatile configurations dataseet differential ta. Any suggestions on how to implement that? This op-amp works as a sort of ‘trip amp’, whenever the input on pin 1 exceeds the voltage on pin 8 0vthe output to the charge pump will go high, being low at all other times.
As I want to know the attached circuit is correct as what you mention? You can then drive the transistor to give you an output of up to Vcc. As i read from d’sheet it can’t do this.
It only can be varying within V output for 40Hz input. Or any other methods can achieve the task? Replacement Transformer Started by ncag 47 minutes ago Replies: But I still cannot be sucessful to make a larger voltage output range. I’m trying to sense the freq of a square wave from 10KHz – 40KHz range. The IC has three basic sections, a trip amp, a charge pump and an op amp, if the charge pump and following integrator can’t be set to the desired time constant then the op amp can give lots of gain.
Forums New posts Search forums.
Media New media New comments Search media. But I need 10khz to 40khz give me a 0 volt – Vcc variation.
The two basic configurations offered include an 8-pin device with a ground referenced tachometer input and an internal connection between the tachometer output and the op amp non-inverting input. I have followed the datasheet of LMN to design a frequency to voltage circuit.
LMN Datasheet(PDF) – National Semiconductor (TI)
I am before use the below circuit and it darasheet. Datasheets, Manuals or Parts. Potentiometer Questions Started by norbss Yesterday at Also, the ripple of the output will affect the output range or not?
BUT As the circuit will lose some voltage it will stop short of 12v out.